FCI ENVIRONMENTAL

Oil and Gas

Offering the latest in wireless remote monitoring and control technologies for pipelines, wellheads, compressors and tank levels. Increase production up time and reduce service costs without ever leaving your office.

Environmental

Monitor for leakage of tanks and pipelines in vapor and water using a system that communicates over the latest in wireless technology. A patented fiber-optic sensor is at
the heart of this solution that can detect a variety of organic and inorganic compounds.

Chemical/Petro-Chemical

Improve your Vendor-Managed Inventory program by cost effectively monitoring your
bulk chemical inventory stored at your end users.

PHA-100 – The Portable Hydrocarbon Analyzer measures and
quantifies petroleum hydrocarbons in the field and in real time eliminating
delays associated with laboratory testing. The PHA also eliminates the
need to use Freon 113 or other solvents to extract TPH from solutions in
order to perform Infrared analysis. Several models of these precision
instruments measure in water and/or vapor.

DHP Digital Hydrocarbon Probe – Measures and quantifies ppm
levels of petroleum hydrocarbons in situ and in real time. DHPs can be
used with our continuous monitoring systems or as OEM sensors with
your data logger. Can be remotely accessed and controlled through a
data logger interface.

CMS-4000 – This Continuous Monitoring System measures
hydrocarbons in water streams. It controls up to 4 DHPs and can be used
to re-direct flow or can be remotely accessed and controlled.

CMS-5000 – This Continuous Monitoring System is a low-cost
alternative for owners/operators of ASTs & USTs. It measures
hydrocarbons in water or vapor interchangeably and controls up to 16
DHPs. It detects leaks from ASTs, USTs and pipelines; monitors
remediation sites, wastewater discharge and storm water. Can be
remotely accessed and controlled.

OilSense®-4000 – This continuous monitoring system is specifically
designed to detect hydrocarbons in produced water at oil production
platforms/facilities. It operates for extended periods without operator
attention, and features auto cleaning, auto zeroing and self-diagnostic
software. Can be remotely accessed and controlled.

PetroSense®-1100 Pipeline Leak Detection System – Developed in
conjunction with the IECC three-dimensional epoxy wrap, Enviromat™.
This system can be linked via satellite to a real-time Internet monitoring
and control system.

LeoLink units are designed to communicate via the Orbcomm Satellite
Network. Orbcomm is optimized for data applications that will transmit
up to 4,000 bytes of information every month. Utilizing data
compression, LeoLink provides an inexpensive solution for monitoring
remote assets.

LeoLink Features include:
Immediate Notification of Lost Production by monitoring up to six
(6) dry contacts and four (4) analog inputs
Faster response/remediation procedures
Production data and/or maintenance information available via the
custom website eliminating the need to travel to the remote site
Control production without a trip to the remote site, using operating
commands such as start / stop or load / unload
Access information using a standard Internet browser; no special
hardware or software is required
Data Compression allows accurate and affordable transfer of information
Summary reports provide data analysis in a clear and concise format
Support for GPS

Via the Internet, you can configure your remote unit. Options include:
Add or modify notification messages for each monitored point
(Asset #1 Start, Unit #100 Stop, Tank #123 Level Low)
Modify analog alarm setpoint levels
Modify digital alarm states (normally open or normally closed)
Change who is notified via alphanumeric or numeric pager or
email. Each unit supports up to twelve notifications for each event

Mobile and fixed asset monitoring powered by Iridium and Norcom
Networks. Applications include the GeoLink 300 and the GeoLink 500 which
provide serial and Amot Hawk-I Modbus communications for remote data
gathering. All products utilize the Operations Center, allowing
you access to reported information via the Internet.

GeoLink 501 - The GeoLink 501A is designed to communicate with the
OPTO22 controller interfaced with USA Compression remote Natural
Gas Compressors. Analog data is collected in the field, generating a
daily report including the current reading, average, daily low and high for
the analog inputs. Remote asset alarms and daily reports trigger a time
stamped message transmitted through the Norcom Geo-synchronous
satellite network, to the Operations Center. Using the
Norcom Geo-synchronous satellite network, the GEOLink 501A can be
deployed throughout North America without requiring local
communications infrastructure. Each remote asset monitoring
system comes with a dedicated Internet web page for monitoring the
remote asset and configuring the alarm broadcast system. Providing the
customer with inexpensive and reliable loss-of-production alarming and
data collection for storage and trending analysis.

Oxygen Measuring System for the non-invasive measurement of oxygen
within sealed packages. OxySense has applications in the food and
pharmaceutical industries.

A novel optical method for the
non-invasive determination of oxygen in packaged food: Up to now,
these measurements were conducted in an optical laboratory with a lot of
complicated equipment. The non-invasive method is, however, much simpler to set-up
and operate. The instrument consists of a small box containing the light source,
detector and the fiber reader pen and is connected to a PC.
It can be used in a lab or outside it.

Advantages of the OxySense 101 System
Measuring oxygen without opening the package (non-destructive measuring technique)
Fast measurement (0.1 second) Specially suited for time series
Accuracy 5% of the reading without individual calibration for a time series of 2 months
Detection limits, typically 0.01 mg/l in water or 0.02% by volume in gas
Easy to operate, can be used in water and air
Independent of pH (2-12) and salt concentration
No interference from gases used in food packaging

These days a large part of pre-packaged food is packaged in a Modified
Atmosphere (MA). MA packaging is one of the most advantageous ways of keeping
perishable products fresh. The basic features of this process
are hermetic seals, high barrier film and gas injection to reduce
the oxygen content inside the packs.